Vol. 34 No. 10(2)
Special Issue on Green Smart Manufacturing Process and Analysis: Part 1
Guest Editor: Cheng-Chi Wang (National Chin-Yi University of Technology)
In this study, we construct a smart home health monitoring application using IoT sensing devices, a Wi-Fi network, and face recognition technologies. The daily activity data of elderly people aro ... Read More
Most existing robot arms are controlled using wired or wearable controllers. A user must enter coordinates or control single-axis coordinate systems so that a robot arm can reach a designated des ... Read More
For the design and fabrication of dies by the deep drawing process, the problems of springback after load removal and the formation of cracks must be considered. In this study, a deep drawing pro ... Read More
In this study, we constructed the mechatronic model of a tool center point (TCP-MM) present in the virtual environment. Since the dynamic behavior of a TCP affects the productivity, geometric acc ... Read More
PC-based data acquisition (DAQ) systems are irreplaceable in terms of capacity and flexibility for data processing. Data acquisition systems serving IoT are a recent development trend. It is nece ... Read More
We constructed a controller for a 500 W proton exchange membrane fuel cell (PEMFC). The controller uses the Arduino Mega2560 control board for system construction and development. The controller ... Read More
S&M3074Research Paper of Special Issue |
|
|
|
S&M3074 Integrating Face Recognition and IoT Sensors to Realize Smart Application of Health Monitoring at Home Chia-Pin Chueh, Kuo-Jui Hu, Yuh-Shihng Chang, and Sheng-Long Kao pp. 3751-3763 https://doi.org/10.18494/SAM4046 Published on October 24, 2022 PDF (open access) |
S&M3075Research Paper of Special Issue |
|
|
|
S&M3075 Wireless Control of Six-axis Robot Arms by Leap Motion Sensor Chin-Chia Liu, Wei-Lun Hu, Chun-Kai Liang, and Chia-Chiang Hsu pp. 3765-3779 https://doi.org/10.18494/SAM4080 Published on October 24, 2022 PDF (open access) |
S&M3076Research Paper of Special Issue |
|
|
|
S&M3076 Analysis of Deep Drawing Process for Micro Square Holes on Copper Sheets Tsung-Chia Chen, Ching-Min Hsu, Cheng-Chi Wang, and Tsui-Er Lee pp. 3781-3796 https://doi.org/10.18494/SAM4082 Published on October 24, 2022 PDF (open access) |
S&M3077Research Paper of Special Issue |
|
|
|
S&M3077 Mechatronic Model of Tool Center Point for Evaluating Dynamic Behaviors for Machine Tools Ben-Fong Yu, Jenq-Shyong Chen, and Hung-Yih Tsai pp. 3797-3812 https://doi.org/10.18494/SAM4093 Published on October 24, 2022 PDF (open access) |
S&M3078Research Paper of Special Issue |
|
|
|
S&M3078 Remote Accessible PC-based Data Acquisition System Pratikto, Muhammad Arman, Ismail Wellid, Nur Khakim, Yean-Der Kuan, and Raydha Zul Fitriani pp. 3813-3822 https://doi.org/10.18494/SAM4094 Published on October 24, 2022 PDF (open access) |
S&M3079Research Paper of Special Issue |
|
|
|
S&M3079 Fabrication, Design, and Performance Investigation of Portable Proton Exchange Membrane Fuel Cell and Control System Chong-Kai Wang, Chia-Shien Chu, and Yean-Der Kuan pp. 3823-3835 https://doi.org/10.18494/SAM4099 Published on October 24, 2022 PDF (open access) |
Cover of this Issue |
 |